Chongqing Dongchong Aluminum Co., Ltd.
Create Value for Society, Help Customers and Help Employees Achieve Their Dreams
Add to Cart
Aluminium Alloy Coil A5052 H32 for Rolling Shutter Door/Corrugated Roofing Sheet
Product specification :
The 5000 series of aluminium alloys represent 5052, 5005, 5083 and 5A05 series. The 5000 series aluminium bar belongs to the more commonly used alloy aluminium plate series, the main element is magnesium, the content of magnesium is between 3-5%. It can also be called Al-Mg alloy. Its main characteristics are low density, high tensile strength, high elongation and good fatigue strength, but it can not be strengthened by heat treatment. In the same area, the weight of Al-Mg alloy is lower than that of other series. It is also widely used in conventional industry. In our country, 5000 series aluminium sheet belongs to one of the more mature aluminium sheet series.
| Aluminium Coil Strip Material |
| 1)1000series aluminium /Pure Aluminum/Pure Aluminium:1050,1060,1070,1080,1100,1350,etc |
| 2)2000series aluminium alloy/Hard Aluminum/Hard Aluminium/Aluminum-Copper Alloy/ Aluminium-Copper Alloy:2011,2014,2017,2024,etc |
| 3)3000series aluminium alloy/ Rust-Proof Aluminum/Rust-Proof Aluminium/ Aluminum-Manganese Alloy:3002,3003,3104,3204,3030,etc |
| 4)5000series aluminium alloy/ Rust-Proof Aluminum/Rust-Proof Aluminium /Aluminum-Magnesium Alloy:5005,5025,5052,5040,5054,5056,5083,5152,etc |
| 5)6000series aluminium alloy / Aluminum-Magnesium-Silicon Alloy /Aluminium-Magnesium-Silicon Alloy /:6101,6003,6061,6063,6020,6201,6262,6082,etc |
| 6)7000series aluminium alloy/ Aluminum-Zinc Alloy/ Aluminium-Zinc Alloy:7003,7005,7050,7075,etc |
| 7)8000series aluminium alloy:8011,etc |
| ALLOY | CHEMICAL COMPOSITION (%) | |||||||||||||
| Si | Fe | Cu | Mn | Mg | Cr | Ni | Zn | Ti | Zr | Other | Al | |||
| 1035 | 0.35 | 0.6 | 0.1 | 0.05 | 0.05 | __ | __ | 0.1 | 0.03 | __ | 0.03 | __ | 99.35 | |
| 1100 | 0.95 | 0.05-0.2 | 0.05 | __ | __ | __ | 0.1 | __ | __ | 0.05 | 0.15 | 99 | ||
| 1050 | 0.25 | 0.4 | 0.05 | 0.05 | 0.05 | __ | __ | 0.05 | 0.03 | __ | 0.03 | __ | 99.5 | |
| 1060 | 0.25 | 0.35 | 0.05 | 0.03 | 0.05 | __ | __ | 0.05 | 0.03 | __ | 0.03 | __ | 99.6 | |
| 1070 | 0.2 | 0.25 | 0.04 | 0.03 | 0.03 | __ | __ | 0.04 | 0.03 | __ | 0.03 | __ | 99.7 | |
| 1080 | 0.15 | 0.15 | 0.03 | 0.02 | 0.02 | __ | __ | 0.03 | 0.03 | __ | 0.02 | __ | 99.8 | |
| 1045 | 0.3 | 0.45 | 0.1 | 0.05 | 0.05 | __ | __ | 0.05 | 0.03 | __ | 0.03 | __ | 99.45 | |
| 1145 | 0.15 | 0.3-0.5 | 0.02 | 0.05 | 0.05 | __ | __ | 0.1 | 0.03 | __ | 0.03 | __ | 99.35 | |
| 1200 | 1 | 0.05 | 0.05 | __ | __ | __ | 0.1 | 0.05 | __ | 0.05 | 0.15 | 99 | ||
| 1235 | 0.65 | 0.05 | 0.05 | 0.05 | __ | 0.1 | 0.06 | __ | 0.03 | __ | 99.35 | |||
| 2014 | 0.5-1.2 | 0.7 | 3.9-5.0 | 0.4-1.2 | 0.2-0.8 | 0.1 | 0.25 | 0.15 | 0.05 | 0.15 | rest | |||
| 2A12 | 0.5 | 0.5 | 3.8～4.9 | 0.3-0.9 | 1.2-1.8 | 0.1 | 0.3 | 0.15 | __ | 0.05 | 0.15 | rest | ||
| 2017 | 0.2-0.8 | 0.7 | 3.5-4.5 | 0.4-1.0 | 0.4-0.8 | 0.1 | 0.25 | 0.15 | 0.05 | 0.15 | rest | |||
| 2024 | 0.5 | 0.5 | 3.8-4.9 | 0.3-0.9 | 1.2-1.8 | 0.1 | 0.25 | 0.15 | 0.05 | 0.15 | rest | |||
| 3003 | 0.6 | 0.7 | 0.05-0.2 | 1.0-1.5 | 0.1 | 0.05 | 0.15 | rest | ||||||
| 3004 | 0.3 | 0.7 | 0.25 | 1.0-1.5 | 0.8-1.3 | __ | __ | 0.25 | __ | __ | 0.05 | 0.15 | rest | |
| 3104 | 0.6 | 0.8 | 0.05-0.25 | 0.8-1.4 | 0.8-1.3 | __ | __ | 0.25 | 0.1 | __ | 0.05 | 0.15 | rest | |
| 3105 | 0.6 | 0.7 | 0.3 | 0.3-0.8 | 0.2-0.8 | 0.2 | __ | 0.4 | 0.1 | __ | 0.05 | 0.15 | rest | |
| 5052 | 0.25 | 0.4 | 0.1 | 0.1 | 2.2-2.8 | 0.15-0.35 | __ | 0.1 | __ | __ | 0.05 | 0.15 | rest | |
| 5A06 | ≤0.40 | 0.000～0.400 | ≤0.10 | 0.50～0.8 | 5.8～6.8 | __ | 0.0001～0.005 | ≤0.20 | 0.02～0.10 | __ | 0.05 | 0.1 | rest | |
| 5005 | 0.3 | 0.7 | 0.2 | 0.2 | 0.5-1.1 | 0.1 | __ | 0.25 | __ | __ | 0.05 | 0.15 | rest | |
| 5050 | 0.4 | 0.7 | 0.2 | 0.1 | 1.1-1.8 | 0.1 | __ | 0.25 | __ | __ | 0.05 | 0.15 | rest | |
| 5154 | 0.25 | 0.4 | 0.1 | 0.1 | 3.1-3.9 | 0.15-0.35 | 0.25 | 0.2 | 0.05 | 0.15 | rest | |||
| 5754 | 0.4 | 0.4 | 0.1 | 0.5 | 2.6-3.6 | 0.3 | __ | 0.2 | 0.15 | __ | 0.05 | 0.15 | rest | |
| 5454 | 0.25 | 0.4 | 0.1 | 0.5-1.0 | 2.4-3.0 | 0.05-0.2 | 0.25 | 0.2 | 0.05 | 0.15 | rest | |||
| 5182 | 0.2 | 0.35 | 0.15 | 0.2-0.5 | 4.0-5.0 | 0.1 | 0.25 | 0.1 | 0.05 | 0.15 | rest | |||
| 5083 | 0.4 | 0.4 | 0.1 | 0.4-1.0 | 4.0-4.9 | 0.05-0.25 | _ | 0.25 | 0.15 | __ | 0.05 | 0.15 | rest | |
| 5086 | 0.4 | 0.5 | 0.1 | 0.2-0.7 | 3.5-4.5 | 0.05-0.25 | 0.25 | 0.15 | 0.05 | 0.15 | rest | |||
| 6060 | 0.3-0.6 | 0.1-0.3 | 0.1 | 0.1 | 0.35-0.6 | 0.05 | 0.15 | 0.1 | 0.05 | 0.15 | rest | |||
| 6061 | 0.4-0.8 | 0.7 | 0.15-0.4 | 0.15 | 0.8-1.2 | 0.04-0.35 | __ | 0.25 | 0.15 | __ | 0.05 | 0.15 | rest | |
| 6063 | 0.2-0.6 | 0.35 | 0.1 | 0.1 | 0.45-0.9 | 0.1 | __ | 0.1 | 0.1 | __ | 0.05 | 0.15 | rest | |
| 7075 | 0.4 | 0.5 | 1.2-2.0 | 0.3 | 2.1-2.9 | 0.18-0.28 | __ | 5.1-6.1 | 0.2 | __ | 0.05 | 0.15 | rest | |
| 8011 | 0.5-0.9 | 0.6-1.0 | 0.15-0.4 | 0.2 | 0.05 | 0.05 | __ | 0.01 | 0.08 | __ | 0.05 | 0.15 | rest | |
| 8079 | 0.05~0.3 | 0.7~1.3 | 0.05 | __ | __ | __ | __ | 0.1 | __ | 0.05 | 0.15 | rest | ||
| Alloy | Temper | Thickness(mm) | Tensile strength(Mpa) | Yeild strength(Mpa) | Elongation(%) |
| Min | |||||
| 5052 | H111 O | >0. 20 — 0. 50 | 170 — 215 | 65 | 12 |
| >0. 50 — 1. 50 | 14 | ||||
| >1.55 — 3.00 | 16 | ||||
| >3. 00 — 6. 00 | 18 | ||||
| >6.00 — 12. 50 | 165-215 | 19 | |||
| >12. 50 — 50.00 | — | ||||
| H12 | >0. 20 — 0. 50 | 210 — 260 | 160 | 4 | |
| >0.5-1.5 | 5 | ||||
| >1.50 —3.00 | 6 | ||||
| >3, 00 — 6. 00 | 8 | ||||
| H14 | >0. 20 — 0. 50 | 230-280 | 180 | 3 | |
| >0.50-1.50 | 3 | ||||
| >1. 50 -3. 00 | 4 | ||||
| >3.00 — 6.00 | 4 | ||||
| H16 | >0. 20 — 0, 50 | 250—300 | 210 | 2 | |
| >0. 50 — 1. 50 | 3 | ||||
| >1. 5- 3.0 | 3 | ||||
| >3.00 — 4. 00 | 3 | ||||
| H18 | >0. 20-0.50 | 270 | 240 | 1 | |
| >0. 50 — 1. 50 | 2 | ||||
| > 1.50 — 3.00 | 2 | ||||
| H22 H32 | >0. 20—0. 50 | 210 — 260 | 130 | 5 | |
| >0. 50-1.50 | 6 | ||||
| >1.50 — 3.00 | 7 | ||||
| >3. 00 — 6. 00 | 10 | ||||
| H24 H34 | >0. 20 — 0. 50 | 230 — 280 | 150 | 4 | |
| >0.50 — 1. 50 | 5 | ||||
| >1,50 — 3.00 | 6 | ||||
| >3.00 — 6.00 | 7 | ||||
| H26 H36 | >0. 20 — 0.50 | 250 — 300 | 180 | 3 | |
| >0. 50 — 1, 50 | 4 | ||||
| >1.50—3.00 | 5 | ||||
| >3. 00—4. 00 | 6 | ||||
| H38 H28 | >0. 20 — 0, 50 | 270 | 210 | 3 | |
| >0. 50~1. 5 | 3 | ||||
| >1. 50 — 3. 00 | 4 | ||||
| H112 | >6.00—12. 50 | 190 | 80 | 7 | |
| >12. 50 — 40,00 | 170 | 70 | |||
| >40, 00 — 80, 00 | 170 | 70 | |||
Photos:
Company Introduction
Chongqing Dongchong AluminumCo,.Ltd. is a manufacturer of Aluminium products with well-equipped,experienced work team.Our company is equipped with international advanced aluminum production lines. We also own press machine, double-sided milling, cutting machine, recoiler, grinding machine, quenching furnace, tension pre-stretching machine, annealing furnace, smelting furnace machine and so on. We mainly provide aluminum and its alloy sheets, plates, strips, circles, foils, embossed coils, colorful painted aluminum coils, sheet products, etc.With a wide range, good quality, reasonable prices and stylish designs, our products can meet most of all customer needs.Our company established in 2002 and have been in aluminium indurstry for more than 15 years.We have our own brand and customized services are available too.We are an ISO9001:2008 certified company and our QC staff members have ten years' experience in this area. To maintain a strict QC system, we not only utilize precision testing instruments but also continuously train our QA personnel regarding the latest testing principles.We have established long term business relationships with customers in many countries and areas in the world, including the USA, Canada, Brazil, India, Chile, Nigeria, Ghana, Italy, etc. We will continue providing high quality products and better services for our customers, and welcome you to visit our company and establish good business relationships with us.